Courier services starting at just R90

MC Project Kits
  • 1.5V Bulb E10 Fits in both our E10 holders. Max input 1.5V
  • 10 ml syringe Can be used for your pneumatic or hydraulic system
  • 2.2V bulb E10 Fits in both our E10 bulb holders Max input 2.2V
  • 20ml syringe Can be used for your pneumatic or hydraulic system
  • The wire is 500mm long and splits into two wires, black and red. Both wires will be 500mm long
  • 4mm thick bamboo stocks 200mm long +-15 units
  • Use this board to build or extend our project. Board MDF
    • Lenth 250mm
    • Width 170mm
    • Thickness 6mm
  • Bobbins x2 Can be used as pulleys Centre hole is 6mm
  • Bridge school project You can build either our Truss bridge or Cable-stayed bridge with this self-build kit. Grab some more sticks under our component section to develop the strength of your bridge even more. This bridge project focuses on triangulation and tension to uphold the bridge's platform. Hydraulic bridge available under project kits Colours of some items may vary.
  • Bulb holder for E10 bulbs the holder can be screwed onto wood to secure it. You will need a star screwdriver to connect the wires. E10 bulbs can range from 1,5V up Typical bulb voltage found in stores are between 2.2V and 3.6V
  • C - Type connector Will produce the voltage of the input connected to it. (indicated on the cell phone charger) This is the female part of a cell phone charger (android)
  • Cell phone tower project kit Included 1 x Wooden base and top | 4 x 350mm x 6mm dowels | 20 x 18cm coffee sticks | 5 x 11,5cm ice cream sticks | 5 x 9,5cm ice cream sticks | 2 x 35mm x 8mm dowels | 3 x Match sticks | 2 x Foam balls | 3 x Cocktail sticks | 6 x paper satellites Not Included Scissors & Glue gun Measurement Base: ±120mm x 120mm | Height: ±370mm (with antennas) Notice - Colours of some items may vary
  • Coffee stirrers 18cm comes in 40g packs (+- 50 units)
  • Construction Crane school project The electromagnet is sold separately. The electromagnet hangs in front of the crane Included Small bag 2 x Sewing bobbin | 1 x 4mm x 25mm bolt  | 1 x 4mm x 16mm bolt | 2 x 4mm nut | 2 x 8mm nut | 1 x Paper clip | 1 x (70mm x 6mm) Dowel | 1 x (35mm x 6mm) Dowel | Round wooden Stopper | 35mm x 10mm Spacer | 40mm x 10mm Handle Medium bag 2 x 1m Rope | 1 x Match box | 14 x 14m Coffee stirrers | 10 x 18cm Coffee stirrers | Corex square | Match stick bag Big Bag 2 x Straw | 4 x (340mm x 6mm) Dowel | Base board | 1 x Top (with 4 holes) | 1 x Top (Middle hole) | Sanding paper Not Included Glue gun and scissors Measurement Base: ±250mm x 160mm | Height: ±405mm The crane can rotate 360 degrees. This project can be used with our electromagnet that hooks on the front. Notice - Colours of some items may vary
  • Crocodile clamps For easy connectivity
  • DC motor Will start turning with 1,5V. Max input 7V If you are using this for a simple project you can cut the white plug off.  
  • The double AA battery holder houses two AA batteries and will have an output of 3Volts
  • E10 bulb holder small Wires are normally soldered onto the holder. It is difficult securing the wire to it without soldering it. E10 bulb holders start from 1.5Volt The typical bulb found in stores range from 2.2V to 3.6V
  • Electromagnet project Included Switch | Battery Holder | 2 x Lugs | 1 x Ferrule | 2 x Cable ties | 2m Electrical wire | Nail | Base Board | Paper clip Not Included Pliers, battery (works best with a good battery) Measurement Base: ±86mm x 35mm After winding the wire around the nail, first test it directly to the battery and see if it is picking up paper clips. Do this before connecting the switch. The colours of some components may vary.
  • Out of stock
    • 30x wire and nail.
    • 6x battery holders with crocodile clips.
    coming soon.
  • Fan

    R52,00
    The size of the Fan is 40 x 40 x 10mm Will spin from 3Volts Max 5Volts input
  • large popsicle sticks comes in packs of 50 units
Go to Top