1.5V Bulb E10Fits in both our E10 holders.Max input 1.5V
10 ml syringeCan be used for your pneumatic or hydraulic system
2.2V bulb E10Fits in both our E10 bulb holdersMax input 2.2V
20ml syringeCan be used for your pneumatic or hydraulic system
The wire is 500mm long and splits into two wires, black and red.Both wires will be 500mm long
All-in-one electrical circuit- Double AA bat holder
- 2.5V Bulb
- Switch
- Electric wire
- Wire for electromagnet
- E10 Bulb holder black
- Screws x 4
- Buzzer
- Wired Croc clamps
- DC motor
- Nail
- Resistor
- LED light
4mm thick bamboo stocks200mm long+-15 units
Use this board to build or extend our project.Board MDF- Lenth 250mm
- Width 170mm
- Thickness 6mm
Bobbins x2Can be used as pulleysCentre hole is 6mm
Bridge school projectYou can build either our Truss bridge or Cable-stayed bridge with this self-build kit.Grab some more sticks under our component section to develop the strength of your bridge even more.This bridge project focuses on triangulation and tension to uphold the bridge's platform.Hydraulic bridge available under project kitsColours of some items may vary.
Bulb holder for E10 bulbsthe holder can be screwed onto wood to secure it. You will need a star screwdriver to connect the wires.E10 bulbs can range from 1,5V upTypical bulb voltage found in stores are between 2.2V and 3.6V
C - Type connectorWill produce the voltage of the input connected to it. (indicated on the cell phone charger)This is the female part of a cell phone charger (android)
Cell phone tower project kitIncluded1 x Wooden base and top | 4 x 350mm x 6mm dowels | 20 x 18cm coffee sticks | 5 x 11,5cm ice cream sticks | 5 x 9,5cm ice cream sticks | 2 x 35mm x 8mm dowels | 3 x Match sticks | 2 x Foam balls | 3 x Cocktail sticks | 6 x paper satellitesNot IncludedScissors & Glue gunMeasurementBase: ±120mm x 120mm | Height: ±370mm (with antennas)Notice - Colours of some items may vary
Coffee stirrers 18cmcomes in 40g packs (+- 50 units)
Construction Crane school projectThe electromagnet is sold separately. The electromagnet hangs in front of the craneIncludedSmall bag2 x Sewing bobbin | 1 x 4mm x 25mm bolt | 1 x 4mm x 16mm bolt | 2 x 4mm nut | 2 x 8mm nut | 1 x Paper clip | 1 x (70mm x 6mm) Dowel | 1 x (35mm x 6mm) Dowel | Round wooden Stopper | 35mm x 10mm Spacer | 40mm x 10mm HandleMedium bag2 x 1m Rope | 1 x Match box | 14 x 14m Coffee stirrers | 10 x 18cm Coffee stirrers | Corex square | Match stick bagBig Bag2 x Straw | 4 x (340mm x 6mm) Dowel | Base board | 1 x Top (with 4 holes) | 1 x Top (Middle hole) | Sanding paperNot IncludedGlue gun and scissorsMeasurementBase: ±250mm x 160mm | Height: ±405mmThe crane can rotate 360 degrees.This project can be used with our electromagnet that hooks on the front.Notice - Colours of some items may vary
Crocodile clampsFor easy connectivity
DC motorWill start turning with 1,5V. Max input 7VIf you are using this for a simple project you can cut the white plug off.
DC Motor without wires. Starts turning from 1.5 - 6V.
The double AA battery holder houses two AA batteries and will have an output of 3Volts
- MDF board (250mm x 170mm)
- Double AA Battery Holder
- E10 Bulb holder x2 (Silver)
- 2.5v Bulb x2
- Push Switch
- Screws x4
- Wire
E10 bulb holder smallWires are normally soldered onto the holder.It is difficult securing the wire to it without soldering it.E10 bulb holders start from 1.5VoltThe typical bulb found in stores range from 2.2V to 3.6V
Courier services starting at just R99
