-
1.5V Bulb E10 Fits in both our E10 holders. Max input 1.5V -
10 ml syringe Can be used for your pneumatic or hydraulic system -
2.2V bulb E10 Fits in both our E10 bulb holders Max input 2.2V -
20ml syringe Can be used for your pneumatic or hydraulic system -
The wire is 500mm long and splits into two wires, black and red. Both wires will be 500mm long -
4mm thick bamboo stocks 200mm long +-15 units -
Use this board to build or extend our project. Board MDF- Lenth 250mm
- Width 170mm
- Thickness 6mm
-
Bobbins x2 Can be used as pulleys Centre hole is 6mm -
Bridge school project You can build either our Truss bridge or Cable-stayed bridge with this self-build kit. Grab some more sticks under our component section to develop the strength of your bridge even more. This bridge project focuses on triangulation and tension to uphold the bridge's platform. Hydraulic bridge available under project kits Colours of some items may vary. -
Bulb holder for E10 bulbs the holder can be screwed onto wood to secure it. You will need a star screwdriver to connect the wires. E10 bulbs can range from 1,5V up Typical bulb voltage found in stores are between 2.2V and 3.6V -
C - Type connector Will produce the voltage of the input connected to it. (indicated on the cell phone charger) This is the female part of a cell phone charger (android) -
Cell phone tower project kit Included 1 x Wooden base and top | 4 x 350mm x 6mm dowels | 20 x 18cm coffee sticks | 5 x 11,5cm ice cream sticks | 5 x 9,5cm ice cream sticks | 2 x 35mm x 8mm dowels | 3 x Match sticks | 2 x Foam balls | 3 x Cocktail sticks | 6 x paper satellites Not Included Scissors & Glue gun Measurement Base: ±120mm x 120mm | Height: ±370mm (with antennas) Notice - Colours of some items may vary -
Coffee stirrers 18cm comes in 40g packs (+- 50 units) -
Construction Crane school project The electromagnet is sold separately. The electromagnet hangs in front of the crane Included Small bag 2 x Sewing bobbin | 1 x 4mm x 25mm bolt | 1 x 4mm x 16mm bolt | 2 x 4mm nut | 2 x 8mm nut | 1 x Paper clip | 1 x (70mm x 6mm) Dowel | 1 x (35mm x 6mm) Dowel | Round wooden Stopper | 35mm x 10mm Spacer | 40mm x 10mm Handle Medium bag 2 x 1m Rope | 1 x Match box | 14 x 14m Coffee stirrers | 10 x 18cm Coffee stirrers | Corex square | Match stick bag Big Bag 2 x Straw | 4 x (340mm x 6mm) Dowel | Base board | 1 x Top (with 4 holes) | 1 x Top (Middle hole) | Sanding paper Not Included Glue gun and scissors Measurement Base: ±250mm x 160mm | Height: ±405mm The crane can rotate 360 degrees. This project can be used with our electromagnet that hooks on the front. Notice - Colours of some items may vary -
Crocodile clamps For easy connectivity -
DC motor Will start turning with 1,5V. Max input 7V If you are using this for a simple project you can cut the white plug off. -
The double AA battery holder houses two AA batteries and will have an output of 3Volts -
E10 bulb holder small Wires are normally soldered onto the holder. It is difficult securing the wire to it without soldering it. E10 bulb holders start from 1.5Volt The typical bulb found in stores range from 2.2V to 3.6V -
Electromagnet project Included Switch | Battery Holder | 2 x Lugs | 1 x Ferrule | 2 x Cable ties | 2m Electrical wire | Nail | Base Board | Paper clip Not Included Pliers, battery (works best with a good battery) Measurement Base: ±86mm x 35mm After winding the wire around the nail, first test it directly to the battery and see if it is picking up paper clips. Do this before connecting the switch. The colours of some components may vary. -
Out of stock
- 30x wire and nail.
- 6x battery holders with crocodile clips.
-
The size of the Fan is 40 x 40 x 10mm Will spin from 3Volts Max 5Volts input -
large popsicle sticks comes in packs of 50 units -
Grain Crusher project Included Small bag Stopper | Handle | 25mm x 4mm bolt and nut | Drawing pin | 2 x 35mm x 5mm Dowel | 2 x 70mm x6mm Dowel Medium bag 14 x 14cm coffee stirrers | 10 x 18cm coffee stirrers | 2 x 100mm cable ties | 5 x 200mm x 6mm Dowels | 1 x 145mm Dowel | Pine plank | 2 x Cam | 2 x T-bar | 2 x 30mm Pivot block | 2 x 60mm Pivot block Big Bag Base | Top | 2 x 340mm x 6mm Dowels | Sanding paper Not Included Glue gun Measurements Base: ±285mm x 145mm | Height: ±235mm Notice - Colours of some items may vary -
Hydraulic Bridge project Included Medium bag 2 x 11.5cm ice cream sticks | 8 x 9.5cm ice cream sticks | Match sticks | Corex Square | 6 x flat sticks | 2 x steel wire | 2 x 145mm dowels | 14 x 14cm coffee stirrers | 10 x 18cm coffee stirrers | 2 x 200mm cable ties | 2 x 100mm cable ties Big Bag 325mm x 150mm Bases | 4 x pillars | 2 x 400mm tubing | 4 x 10ml syringes | A4 board Not Included Glue gun & scissors Measurements Base: ±320mm x 150mm | Height: ±170mm (when closed) Notice - Colours of some items may vary -
Hydraulic Crane school project (excluding electromagnet) The electromagnet is sold separately. It hangs in front of the crane Includes Small bag 1 x 8mm Dowel | 2 x Sewing bobbin | 1 x 4mm bolt | 1 x 4mm nut | 2 x 8mm nut | 1 x Paper clip | 2 x (70mm x 6mm) Dowel | 1 x (35mm x 6mm) Dowel | Round wooden Stopper | 2 x Screws | 35mm x 10mm Spacer | 40mm x 10mm Handle Medium bag 1 x Plastic saddle | 1m Rope | 3 x 100mm cable ties | 2x 200mm Cable ties | 1 x Match box | 14 x 14m Coffee stirrers | 10 x 18cm Coffee stirrers | 2 x (30mm x 25m) Pivot Blocks Big Bag 800mm tubing | 4 x 20ml Syringe | 2 x (400mm x 6mm) Dowel | 4 x (340mm x 6mm) Dowel | 180mm x 250 Base board | 2 x (60mm x 60mm) Top and base | Sanding paper Measurements Base: ±225m x 180mm | Height: ±375mm The crane can turn between 0 and 90 degrees. The arm can also raise and lower using hydraulics. Notice - Colours of some items may vary -
This is a hydraulic or pneumatic component kit use it for Jaws of life, hydraulic jack, hydraulic bridge ect. Included: 1x 20ml syringe 1x 10ml syringe 400mm tubing 2x Cable ties -
Jaws of life project Grade 7 Make either a 2 lever or 4 lever Jaws of life Included Plank | 4 x Flat sticks | 2 x Split pins | Bolt and nut | Tubing pipe | Carton jaws | Syringe 20ml | Syringe 10ml | 4 x Cable ties | Wire Not Included Scissors Measurement Length: ±500mm | Plank breadth: ±20mm | Jaws breadth: ±130mm The colours of some items may vary -
Jaws of life project Spreader and Cutter Make either the spreader or the Cutter with this kit Includes Small bag Wire |4 x Split pins | Box | T-bar | 3 x Flat sticks | 200mm Tubing pipe | Spreader and cutter paper jaws | Syringe 20ml | Syringe 10ml | 2 x Cable ties The box is used to draw and cut out the spreader or cutter that you want to use in your project. Not Included Scissors | Glue Measurement T-bar: ±155mm x 125mm Notice - The box the project comes in may vary in colour (white and brown). The colour of some other items may vary. -
This is our material kit for the shelter structure Use this kit with our shelter structure (Frame) to design your shelter. Our Frame structure can be found under project kits The kit includes 2 x A4 brown cardboard paper 1 x Corrugated sheet 1x Corex sheet 1 x Netting 1x Clear sheet (for windows or roof openings) 1x waterproof fabric Have fun and be creative. We currently do not have a video for the enclosure of the shelter. Please view the frame structure video on our site. -
Mine Shaft Headgear project Included Small Bag 1 25mm Bolt and nut | Handle | 1m Rope | 1 x Wooden stopper | 1 x Sewing bobbin Small Bag 2 Box base and top | 4 x 55mm dowels Medium Bag 2 x 50mm Pivot blocks | 2 x 100mm dowels | 16 x 18cm Coffee stirrer | 1 x 9,5cm Ice cream stick | Circular polystyrene | 2 x Correx circles Big bag 1 x Wooden base and top | 4 x 350mm x 6mm Dowels | Sanding paper | 2 x Straws Measurements Base: ±200mm x 150mm | Height: ±375mm Tip: Use the sandpaper provided to sand the foam pully before assembling. Notice - colours of some items may vary. -
Mini Cell phone tower project Included Small bag Match sticks | 1 x tooth pick | 1 x foam ball Medium bag Top | Base | 12 x 18cm Coffee stirrer | Paper Satellites | 4 x 200mm dowels Not Included Glue gun & scissors Measurements Base: ±90mm x 90mm | Height: ±260mm -
Push switch Easy wire connection pins insert wire and turn to lock -
Rocker switch our rocker switches typically have a max voltage of 12Volts This is a two-pin switch. Joins and breaks the flow of current in a single wire -
This is our shelter frame structure (shelter project) Build any of our 3 designs or create your own. Enclosure materials are sold separately under project components The base board is 150x190 the height will change according to your design. Have fun and be creative. Focus on evaluating your structure and using strengthening methods like triangulation to support weak points.
Courier services starting at just R90
